Sensing-Saf-Start® Products
An affordable and effective way to stay safe and adhere to compliancy requirements.
Made in the U.S.A.
• Upgrades small machines to the latest safety requirements by preventing automatic restart accidents after a power interruption.
• Plugs into a machine power cord and plug (Model #1996).
• Permits the use of the machine’s “on-off” switch.
• Complies to the latest OSHA and NFPA safety standards.
• Replaces old, frayed and dangerous, “ungrounded” power cords (Model #1997, #1998, and #1999).
Model #1996
Short extension cord style features a 14″ cord on male plug end and a 12′”cord on female receptacle end.
Technical Details:
• 120-Volt A.C
• 50/60 HZ
• 15-Amp Maximum
Description:
For use on all 120-volt machines that have good power cords on them. Plugs into the machine power cord.
Model #1996 is listed with Underwriters Laboratories, Inc. for the U.S. and Canada (File #E62632)
Model #1997
Features a 20″ cord to equipment switch and 8-foot power cord with molded NEMA 5-15 plug on cord end.
Technical Details:
• 120-Volt A.C
• 50/60 HZ
• 15-Amp Maximum
Description:
For use on 120-volt machines where the power cord is old and/or you want the reset button closer to the machine for easy access.
Model #1997 is recognized under the component program of Underwriters Laboratories, Inc. and for Canada (File #E62632)
Model #1998
For in-line wiring with 20″ cord to equipment switch and 8-foot cord to power supply. No plug provided.
Technical Details:
• 120-Volt A.C
• 50/60 HZ
• 18-Amp Maximum
Description:
For use on all 120-volt machines where the power cord is old and/or you want to connect to a disconnect box or you want to install a 20-amp plug or a twisting locking type plug on the cord.
Model #1998 is recognized under the component program of Underwriters Laboratories, Inc. and for Canada (File #E62632)
Model #1999
For in-line wiring with 20″ cord to equipment switch and 8-foot cord to power supply. No plug provided.
Technical Details:
• 200 to 240-Volt A.C (single phase)
• 50/60 HZ
• 15-Amp Maximum
Description:
For use on all 200 to 240-volt single phase (3-wire) machines. You must install any matching plugs on the power cord.
Model #1999 is recognized under the component program of Underwriters Laboratories, Inc. and for Canada (File #E62632)
HOW IT WORKS
When a Sensing-Saf-Start® is installed on any piece of equipment and there is an electrical power interruption to the equipment, the Sensing-Saf-Start® will open the circuit so when the power source is restored, the Sensing-Saf-Start® will not reset until the equipment switch has been turned “off”. There is a sensing circuit within the Sensing-Saf-Start® that sends a signal up to the equipment switch to see if it is in the “on” position. If the switch is still “on”, the Sensing-Saf-Start® sounds a warning buzz when the reset button is depressed, and it will not close the circuit until the equipment switch is turned “off”. Then, and only then the Sensing-Saf-Start® will close the circuit so the equipment will operate again.
Warning for California Residents View Details
The easy to install and inexpensive solution to the OSHA anti-automatic restart requirement.
Sensing-Saf-Start® can be installed on most equipment in minutes.
• Drill Presses
• Band Saws
• Belt Sanders
• Small Milling Machines
• Small Air Conditioners
• Tool Grinders
• Disk Sanders
• Power Hacksaws
• Stress Test Tread Mills
• Small Lathes
• Cut-Off Machines
• Table Saws
• Polishing Machines
• Scroll Saws
• Radial Arm Saws
• and so much more
PLEASE NOTE: WE ARE REGISTERED IN THE GOVERNMENT’S SYSTEM FOR AWARD
MANAGEMENT (SAM) WITH OUR CAGE CODE #63752 AND DUNS #076363696
Location
8863 Greenback LN, #311
Orangevale, CA 95662
PHONE
Office (916) 933-2699
Mobile (916) 397-6668
Fax
(800) 486-4993
Int’l (916) 933-4993